Today I will show you a flower shape, called Hop (Hop-shape). Usually we use Shaped Foliages to create such a shape (Hop-shape)
I'll use the Lutescens and I trim it out of it
In general, the width of this leaf (Lutescensf) is six inches, we have to use scissors to show up, whenning reaching about half of the leaf，we trim slightly bent to the top
Pruning the other side, you can hold near the middle of the stem, with just the way to trim, resulting in this appearance
As for the remaining part of the Lutescens, I cut its stem into eight inches long
The method of pruning is a bit different, and we can trim it slightly obliquely
the most important thing for flower arrangement is how to create shape, the two leaves (Lutescens) are 22 inches and 19 inches
These two palms (Lutescens), I will put them into this shape. We can bend the Lutescens to make their shape more beautiful
I put the first piece of Lutescensin the foam at ten o'clock position, the other placed in its opposite, causing the shape
Next, I put these two pieces on both sides. We can place the left and right leaves down here，we can also press the leaves to the level
We do not put it flat on the table, but to take it up, and press the leaves down .
And then we placed the leaf in the left side 4 o'clock and right side 8 o'clock of the foam . I called these two positions the "Golden Position"
I put the Lutescens into this shape, I call it Hop-shaped (Hop-shape)
We have seven steps, first placed with Shaped foliage, causing lines, and then I will put high flower, I took out a relatively straight carnation, about 16 to 17 inches, placed in the foam surface 12 o'clock position
Usually the distance between flowers and flowers is about three inches, so the second is 13 inches, put it in the foam surface three o'clock position
We placed the highest two carnations, and then placed in the left and right one, their length is the highest that half of the branch, that is, 8 inches
Of course, if we want to do this work a little bigger, we have to adjust the length of the flower
Now I put the two on the left and right sides of the Lutescens above
Then I will put the main flower in the focus of the location, because the location is relatively narrow, we are not suitable to use too many flowers to do the main flowers, today I use white lily (White Lily)
The two white lily (White Lily) are 11 inches and 8 inches, I put them in the foam nine o'clock and six o'clock, slightly tilted forward, if from the side, will see this potted Before, so as to make a level
I now enter the fourth step, that is, placed leaves, we can choose large tracts of Sabah leaves, feet reserved for an inch into the foam OK
We first prepared five, the first placed in front of six o'clock position, so that the seat of the Sabah leaf spire forward, and then in the left nine points and the right three points each placed a piece
And finally placed two in the corner, that is, seven o'clock position and four and a half position
Then I will deal with other space, I call this part of the main area, and placed in the palm(Lutescens) within the range of flowers, we call these accompany flowers
We put these finished, you can also put flowers in the next side. I placed a five-inch carnation in the foam side of the six-point position, and then placed in its left and right, about five to six inches, forming a curve
In addition, I placed a 10-inch carnation here, and in the foam surface five and seven o'clock position placed an 8-inch carnation
You can see how I put these flowers in accordance with the steps.
Then I will put the leaves, first of all I will put a nine-inch Sabah leaves in the back, as the back leaves
In addition I will cut some of the smaller Sabah leaves, placed in the foam side and front position
As for the middle position, I will place the kamini , cut them into four to seven inches
After the cut, put them between flowers and flowers, used to cover the foam
In fact, the leaves are divided into two kinds, we call a piece of Sabah leaves the "flat leaves", and "fine leaves" for a bunch of leaves like Kamini .
We can put leaves in these locations, about eight to 90% of the space will be sufficient, because in the end we will put fine flowers
Today I will use yellow peacocks, we can put some slightly tall flowers. First I cut a 15-inch yellow peacock, placed on the side of the highest carnation
Alternatively you can choose a smaller yellow peacock, about 12 to 13 inches, put it on the side
For a layer , I then cut a 10-inch yellow peacock to place here
As for the left and right sides, I will put two 11-inch yellow peacock
In front of the other space, we can then put the yellow peacock, about seven to eight inches, to pay attention to the top of the yellow peacock is pointed down
I will place some 8-9 inch yellow peacocks in these locations
For the rest of the Yellow peacock ,we can cut it out and then put a few into a bunch
We can see that today I demonstrated the primary flower arrangement, I call it "Hop", it is formed by the above and left and right a total of four pieces of Lutescens(Lutescens)
I hope you keep in mind the seven steps of flower arrangement, that is, Shaped Foliage High flower, main flowers, grass, Accompany flowers, Grass and Fine flowers. Hope that we can practice more.
For more infomation >> VẤN NẠN HỌP LỚP HIỆN NAY | TUN PHẠM VLOG - Duration: 1:11. 
For more infomation >> Thịt lợn và những nỗi sợ khó lường cứ 100 người ăn thì 99 người mắc bệnh - Duration: 6:34. 
Không có nhận xét nào:
Đăng nhận xét