Today we're going to address the indexing system for the tough workhorse
automatic screen printing press coming up well the next things I'm going to do
is I'm going to replace this part here with a new little V block essentially
what this does it grabs on to this little bearing here this one is a little
worn looks like we got ourselves a couple half-inch maybe nine sixteenths
here I'm going to go ahead and remove that install this new block
oK we've got our old Vblock removed we're gonna put the new one in next
thing I'm going to do is I'm going to clean this rail up here and this is well
basically how the press indexes is to grab the hold here and then this
cylinder pushes the whole thing forward but what I'm going to do is I'm gonna
take some compressed air and blow out a lot of this lint clean these rails up a
little bit and didn't reduce them with a little bit of lithium grease
we've also hit this part of the rel here's our little bump stop here just
trying to clean some of this grime and crap out I'm gonna clean this track up
the best I can and then put a little bit of grease I'll push this word a little
bit clean this part of the track as well all right our track is looking a little
cleaner I'm gonna take some lithium grease here
I'm just gonna run it on the inside these rails I'm gonna do the same thing
over here I'm going to move this back now I'm going to grease this track here
put her to have a grease here
excess and I'm going to move this guy in put a DAB here work that back for stick
the roll back here and I'm going to lube the inside of this row far down as I can
reach
like real nice and lubed up alright next thing I did is I greased this up just a
little bit to try to force some lifting three from there
we can love it my head and took care of that I'm gonna go round to each one of
these stations you see I already started working on this one
pushing a little lithium grease inside this roller bearing and putting a little
bit of lithium grease inside these sports so I'm gonna go back and wipe up
the excess also went through and packs and lifts in grease into each one of
these bearings that is part of the index in the system that little fork grabs a
hold of it and pushes the press and yes swing secure so last but not least there
are these little roller bearings here as you can see it does have a little plate
that or just a guide that it rolls up and down on I'm gonna clean up some of
this old grease it doesn't look too bad but I'm going to leave all three of
these up as well while I'm at it next thing I'm going to do is I'm going to
crawl under here and adjust one of the little blocks the lift cylinders used to
push up on the carousel itself it looks like one of the lift cylinders was
replaced and that was not properly adjusted I'll show you what I'm talking
about here's a little block that has at the
end of the lift cylinder if I try and move the press a little bit you can see
it is dragging this was loose so I ended up tightening it up now that tightened
it up it is dragging a little bit there's not
a groove worn at the bottom or anything I did grease the bottom of this
the entire press but I'm going to use a couple wrenches to break this free and
then I'm going to use some filler gauges and check the other ones see where
they're at find kind of a happy medium or this guy who said it here is the
other one let's see if we can slide a feeler gauge twenty and thirty one
hundred Spiller gauge and I'm gonna use that is so what's the distance is I'm
gonna said that if I get these things stick together stay together but either
wrap them up with some tape very own wrapped a little some tape
but part slide this in the myths of recording how to lock down those I don't
even know what they're called I mean they're basically little blocks at the
end of the lift cylinders you essentially lock this down you pinch
them down together and then that will secure one of the things I will have to
do though Howard my press tag did show me how to adjust the table it's a touch
out of whack as I spin the press you can see that one side is a little bit lower
than the other but I'll save that for a future video which means I will also
have to go back and adjust each one of these palettes make sure my off contact
is the same from station to station how I will go about doing that is using some
either a piece of metal that is about the thickness of the off contact that I
want setting it on each station I'll table it up with my pallet down and I'll
raise the pallet up until that piece of metal meets the screen-printing frame
and then I'll set it and level it from there but I'll have to save that for a
future video as well just fine-tune it you got to fine-tune it it definitely
needs it that's about it for today guys keep an eye out for next video I'll show
you how I went about rebuilding some of these heads and addressing some of the
maintenance issues that I did don't forget that we are an official rep for
cast fit productions use our promo code Mikey designs at Katz's Pitt screenprint
supply.com you'll get five dollars off your screen
printing supply or equipment purchases and what it does is it will help fund
our channels that way we can continue to make videos such as these for you
subscribe give this video a thumbs up share our content leave a comment below
even if it's just a hello and we'll see you guys next time
For more infomation >> Thái bình quê lúa//Cảnh cúng lễ tại CHÙA ở quê - Duration: 12:19. 
For more infomation >> NOCH Modellbau-Winter Basteltipps | Weihnachtsmarkt ausschmücken | Adventskalender Folge 17 - Duration: 2:09. 
For more infomation >> War Thunder gameplay en español. # 1.83 la noche. =AMM0= escuadron. - Duration: 3:01:19. 
For more infomation >> Süper Azeri Şarkı ( Ağlatan Kafe melodisi ) DUYGUSAL 2019 - Duration: 3:24. 
Không có nhận xét nào:
Đăng nhận xét