Hi YouTube Hello everyone welcome to Animal Land
Do you know what this is?
That this is put in place. I think I know who knows what will start from now
A good way to intude. Or, whether it's good or bad, I know who I know
OK, Let's get started
I have to tell you what to start. Adjust the spokes
Remove the wheel runout. Let's get started
I will setup up here
This is Wheel Truing Stand I can fold like this
Well you can leave it in the corner of the room or the corner of the garage.
It may be a corner of the workshop
When I use it I do like this
When I release the arm, I will open this place next time
Can you see it?
I will remove the cap attached at the end
Remove both. I'll leave it here.
Open up to the width where the wheel will fit. I think that it would be better to open it widely
It's a little too wide, but I do it like this
I will set the wheel here
Um
Mountain spokes replace
So
Let's check this. Since I was riding for 30years, how far is it swinging
I already think that I will change it after cats, so I will remove them all
I firmly got it
It is in such a state
OK
This time spoke ... different
It is a tool to check if the rim is not swinging
When I bought it will be shifted gradually even though it is beautiful
I will explain why I can swing
There are lots of spokes here. Spokes are extending from both sides of the hub
It is such a feeling when it is a body
Suppose there is a rim at the end of the hand. The spoke is coming out of the shoulder
At first this is even. The rear wheels are not even.
Suppose that it is equal. It's in a state of fit
The screw loosens and the spokes stretch while running
This will come loose and grow
I am in a state of tension, so I will shift to this place
This is because it will grow. Conversely, when the left hand stretches it can swing to this side
Because there are some places that have not swung, I will move like this
How to fix it
If I stretched to the left side
Pull the other side to return to the middle. This is how it works
So, with this
Since there are spokes extending from the left and spokes extending from the right, For example if you are distorted on this side
Tighten the spokes on the other side. Or loosen the side spokes a little.
I will return to the center while making such adjustments
OK, first check if they are misaligned
I'll make this stick beside the rim.
I'll try
Since there is a rim here, I can bring it closer to the rim
Because this is an open state it closes
Then I hit it in a certain place. Then I will move it a little.
I do not know how long it is running so I will release it a little more and check it
I have not swung much.
It's not funny. Then, bring the arm a little closer
You can see how to move closer
I'm running a little.
I wonder if I understand this
I have zoomed in a lot. Is it easy to see?
I will zoom in a little more.
Please look at the gap between the shadow and arm reflected on the rim
Then, I will try
You got closer now
There is a place to approach.
Maybe it is around here
It will be very close here. I will try again
It is shaking great only here
Here. We will make the camera wide
The point where I was swinging is next to the valve
This is around here. I will add a sign
Here it is.
Here comes close at hand
Become quite close here
I fix it so as not to approach
I am running to here
Tighten this spoke instead of this spoke
I pull a little over there
Shake removal is easy to understand
I think it's easy
A little more
A little more
I adjusted again so I will check again
I did not come close suddenly
here
Mark passes I did not do it.
here Among them, in this position until a while ago
It is near again
I have to fix this part a bit more
It is still close.
A little more
Sounds good
It is like this
OK
With this you can remove the runout of the wheel
If maintenance of the wheel is not possible
The brake and the rim will get hit.
I think that you have experience as a mamacheari
It will not occur if maintenance is done
It is in a very beautiful state
It is better to adjust the tension as this wheel is much used
It is not so loose
Although it seems to be good even if you tension up
Perhaps because it is old, it will be torn as soon as it is tightened
Spokes are about to break
I will exchange all the spokes
This time I did maintenance on the wheel
OK, how was it? This time I did the maintenance of the wheel
Is there anyone who seemed to be able to easily maintain the wheel maintenance unexpectedly?
Knowing the reason
Pull the right when you go to the left, pull the left when you go to the right
That is the only reason
So I wonder if I can do it little by little
It is attention to pull too much
It will be torn or warped
Attention is necessary
I think that it is easy to do unexpectedly if I understand the theory
Tool for maintenance is expensive and its size is big
I think that it is good to challenge
At first it is good to try with a wheel that is not expensive
Next time I will tension up Ultegra's spokes
I used this wheel for about 2 years. I got 7 thousand kiloliters.
Adjust the tension. Tension up:Strengthen spoke tension
I think that it will probably be relaxed. Tension up and return to the feeling of a new item
I'll try it
I think that this will end with this time.
Thumbs up please if you are interested in this video as a reference
Thank you for subscribing to the channel
Bye!
There are many other videos at Animal Land Please do watch this kind of delivery and such
Không có nhận xét nào:
Đăng nhận xét