Hello everyone! With you Catherine and Obustroeno
We continue to work on our orchid. Today we will deal with leaves and final assembly
Ideally, use 2 mm craft foam or 2 mm Eva foam for leaves
We will need: 1) 2 mm eva foam; 2) oil pastels; 3) zephyr eva foam; 4) wire; 5) acrylic lacquer; 6) a soldering iron and rosin; 7) polystyrene; 8) tape tape
I will use the template 2 - bigger and smaller leaves
Circle with a toothpick
Do not try to make the leaves symmetrical
We will need 4-6 leaves
You can cut 2 leaves at once
Take oil pastels
I took different shades of brown, dark green, light green and gray
Drawing the center
You can draw with a ruler
From edge to edge draw stripes
All stripes must meet at the top.
Take a shade more darkly. Between the drawn stripes draw more stripes
Edges can be darkened a little stronger.
Add a light shade
A little brown
Do not overdo it
Bottom tinted in dark brown
Take a piece of foam rubber and pound
Here's what it should turn out to be
Similarly, decorate the reverse side of the leaf
Take a piece of zephyr eva foam
Thin out
Glue wire
Tint a bit
Under the color of the leaf
And paste from the wrong side. I will glue on Cosmofen
Now you need to cover the leaves with acrylic varnish
Soft brush
I always cover in two layers
With the obverse and the reverse side
While the leaves are dry, let's do a sprig
You remember that she remained in this state
Separate all white wires. This is our +
And all red
We will need to clean them and connect
Cut to the same length
Clean
And twist together
Do the same with white wires
The role of the adapter will perform charging for the phone.
Clean the wiring. In most cases, white wire +
Dark -
To avoid mistakes, curl + with +
When you connect for testing, two strands must not touch
This is a temporary mount, then we solder it
That's apart from each other
And check
Checked - flowers glow
Now you need to fix the twist
I recommend closing this part of the wire with a heat-shrink tube - it will be more beautiful
This part can be wrapped with a tape so that it is not visible.
Put the soldering iron to heat up, and we solder + to +, and - to -
For an orchid, I took this kind of pot, it is ceramic
I made a hole with a drill for ceramic tiles
Somewhere in the middle
Stretch the end of the wire
So that the whole ugly part was inside the pot
And from the hole there was a wire for connecting
Dip both ends in rosin
On the orchid also
We solder the second pair of wires in the same way.
This part must be insulated from each other.
So that they do not touch
This can be done with tape or hot glue.
Done. We can test
Cut the piece of polystyrene by the diameter of the pot
Paste the polystyrene with hot glue
Now we can insert flowers
Fasten the leaves
Put inside the pebbles
Ideally, you can make roots
If you are interested in how to make them, write in the comments and in one of the videos I will show
For more infomation >> Airfix Dogfight Doubles Pearl Harbor Gift Set Model Kit Build & Review - Duration: 5:28. 
For more infomation >> Opening 100 Qinglongmon boxes - Digimon Masters Online - Duration: 2:25. 
For more infomation >> Barış Hoşadam - Ahsas ft.Tales (Official Music Video) - Duration: 2:55. 
For more infomation >> DSK - Tuyển Tập Nhạc Miễn Phí Vol. 1 - ĐHHAILTCSĐ - Duration: 17:59. 
For more infomation >> ❤️ Красивое Пожелание СПОКОЙНОЙ НОЧИ❤️ Сладких снов❤️#Мирпоздравлений - Duration: 2:20. 
For more infomation >> Kendi Yaptığım LOL Fashion Crush - Slime ile LOL Sürpriz Jelly Fashion Crush - Duration: 6:57. 
For more infomation >> WATER BALLOON PULSE CROSSBAR CHALLENGE w / SESEGEL - Duration: 10:19. 
For more infomation >> Мультики для детей с Игрушками автобус Тайо - Автобусные гонки! МУЛЬТИКИ ПРО МАШИНКИ для мальчиков - Duration: 6:51. 
For more infomation >> NEW PARANOID PRANK! (Franklin, TN 2018) - Duration: 3:03. 
Không có nhận xét nào:
Đăng nhận xét